Tools

Precision-machined anodized aluminum tool designed to allow for easy installation, removal, or adjustments of the Shimano Hollowtech II Crankset compression bolt.

This 29mm open bore adapter is used to press 29mm x 42mm (DUB) sealed bearings. The adapter is machined with one step at 29mm OD, which fits into the center of the sealed bearing. For use with Wheels Mfg. bottom bracket press (PRESS-7 , PRESS-7-PRO or PRESS-9-PRO). - Inner step outer diameter: 28.9mm - Outer diameter: 41.8mm - Thru hole diameter: 12.8mm (1/2-inch) - Thickness: 7mm - Machined, red anodized aluminum - Sold individually

Precision-machined anodized aluminum designed to allow for easy adjustment of the Fox DHX2/FLOAT X2 shocks requiring a 3mm and 6mm hex wrench. This small, pocket-sized tool allows for easy trail-side adjustments.

Wheels Manufacturing Sealed Bearing Extractor - 17mm Fits the following bearings: - 6003 - 6803 - 6903 - 17287

- Headset drift for sealed bearing installation press - Drift is machined with steps to press in headset cups that use either 1-1/8" or 1-1/2" bearings, but may be used for other cups with odd-sized sealed bearings - Compatible with bearing presses using 1/2" diameter rod, such as Wheels Mfg Headset Cup Press (PRESS-8)

Wheels Manufacturing Sealed Bearing Extractor - 10mm Fits the following bearings: - 6000 - 6200 - 6800 - 6900

- Drift and over axle set for common thru axle hube and frame bearings - For use with 3/8" press rod - See wheelsmfg.com for full list of contents

Another indispensable tool for the professional bike shop. The hub bearing press pro kit works with bearings that have an i. D. Of 10mm or smaller (most front hub sealed bearing fall in this range). Installs sealed bearing sizes : - 6801 - 6802 - 6803 - 6900 - 6901 - R6 - 688 - 608 - 609 All parts are laser etched for easy identification. Formally press-2 includes: - 608 open bore 5mm x 2 - 608 over axel 5mm x 2 - 609 open bore 5mm x 2 - 609 over axel 5mm x 2 - 688 open bore 5mm x 2 - 688 over axel 5mm x 2 - 6801 open bore 5mm x 2 - 6801 over axel 5mm x 2 - 6802 open bore 5mm x 2 - 6802 over axel 5mm x 2 - 6803 open bore 5mm x 2 - 6803 over axel 5mm x 2 - 6900 open bore 5mm x 2 - 6900 over axel 5mm x 2 - 6901 open bore 5mm x 2 - 6901 over axel 5mm x 2 - R6 over axel 5mm x 2 - Rear QR skewer All parts are laser etched for easy identification.

- SRAM Thin Flange T47 Bottom Bracket Socket Designed to create a tight grip on thin flange bottom bracket to avoid slipping while torquing cups into bike frames. - This single-sided socket is used for installing and removing 52mm, 16-notch bottom bracket cups. - The socket has a machined 3/8" drive, which can be used to allow 3/8" drive torque wrenches to be attached and locks onto a 1/2 inch UNC press rod for secure and easy installation of thin flanged bottom brackets. - Machined 6061 Aluminum Anodized Red

- Machined to match manufacturer specifications and designed to be used with a ½” drive socket or torque wrench for easy installation and removal of e-bike lockrings. - Precision machined aluminum body. - Anodized in Wheels MFG red.

Designed to press in all current wheels mfg bottom brackets! our universal bottom bracket frame drift is designed to press all current wheels mfg bottom bracket cups in to your frame. The adapter is machined with multiple steps to fit common bottom bracket shell inside diameters listed in the compatibility tab below. Each step is laser etched with the diameter size. Drift can also can be used as a frame bottom bracket shell sizing guide! - Inner hole sized to fit 1/2" threaded rod. (Not for use with our Press-1 or Press-4 ) - Compatible with any other press with a 1/2" diameter rod - Recommended for use with Wheels Mfg BP0006, BP0007 - Machined aluminum - Anodized red - Sold individually We do not recommend it for use with press with a rod diameter less than 1/2". When used with a smaller rod, it is almost impossible to prevent the cups or bearings from pressing in straight.

Complete tool kit for installing wheels manufacturing bottom brackets. Kit includes our new bottom bracket socket tool for installing our BB cups, along with new sealed bearing drifts for the following ID bearings: - 22mm - 24mm - 29mm - 30mm Bottom bracket press pro install kit includes: - UNC 48mm 16-notch socket x 1 - 22x37 drift 1/2" x 1 - 6806 OB 1/2" x 2 - 24x37 OB 1/2" x2 - 1/2" frame drift x 1 1/2-13 x 9. 7" - threaded rod unc x 1 44-48. 5mm - double 16-notch 1/2" socket x 1 - threaded handle x 2

- These sockets have a machined 3/8" drive, which can be used to allow 3/8" drive torque wrenches to be attached and locks onto 1/2 inch UNC press rod for secure and easy installation of thin flanged bottom brackets - Machined 6061 aluminum in anodized red - Made in the USA

Precision machined anodized aluminum clamps designed to allow for easy and secure clamping of round suspension components. Designed with strong magnet inserts to keep the shaft clamps securely in place when used with a vise clamp. Includes 1 pair of of shaft clamps to fit shaft diameters 8mm 9mm 10mm 12.7mm 15mm 15.9mm 16.7mm

BB30 service kit for SRAM DUB cranks. - Includes (2) Enduro 6806/29 ABEC-3 sealed bearings and 2 retaining clips - Bearing Dimensions: OD: 42mm / ID: 29mm / Width: 7mm - Enduro ABEC-3 bearings - Use with SRAM DUB cranks Note: SRAM DUB cranksets are not designed to work in 68mm or 73mm wide shells with inboard bearings. Use only if your frame is a direct-fit bearing system, and the BB shell width is 86.5mm or wider.

Individual extractor for removing 6806 sealed bearings with 29mm inside diameter. These bearing extractors grip the inside race of a sealed bearing, allowing the bearing to be tapped out of the hub shell or frame component. Insert the extractor into the bearing, tighten one side with a matching wrench, and the collet expands to grip the inside of the bearing. Tap the extractor bearing out together with a punch and hammer. All extractors are size specific! If attempting to remove a bearing of a different size than the extractor, you will permanently damage or break the extractor. If the extractor is smaller than the bearing, try using a shim between the extractor and the bearing to get the tightest fit before tightening the extractor bolt.

Shock Bushing Press Kit An evolution of our original bushing toolset which required the use of a hammer to pound out shock bushings. The new design uses our threaded handle press system to easily and efficiently remove shock bushing in 12mm and 1/2 inch sizes. - Fits 12mm and 1/2" bushings. - Machined aluminum - Anodized Red

Wheels Manufacturing Sealed Bearing Extractor - 12mm Fits the following bearings: - 6001 - 6801 - 6901

Shimano XTR M9100 Crank Fixing Bolt Replacement - Aluminum - Sold individually - Replacement crank fixing bolt for Shimano XTR FC-M9100. Use if the existing bolt gets cross-threaded or stripped. Use our XTR-CAP-DRIVER to remove the self-extracting cap to allow for replacement. - Remove crank arm bolt cap from crank. Remove damaged crank fixing bolt, being sure not to lose the thin cone washer. Insert the new crank fixing bolt and reinstall the crank arm bolt cap. When installing cranks, tighten crank fixing bolt to 45-55Nm (oem spec).

- These sockets have a machined 3/8" drive, which can be used to allow 3/8" drive torque wrenches to be attached and locks onto 1/2 inch UNC press rod for secure and easy installation of thin flanged bottom brackets - Machined 6061 aluminum in anodized red - Made in the USA

Wheels Manufacturing Over Axle Adapters are used for pressing your most commonly used bearing sizes into place. Each represents an excellent addition to the Press-4 Bearing Press. - Adapters sold individually

Use this double-sided socket tool for installing and removing both 48.5mm and 44mm 16-notch bottom bracket cups. Socket is machined for 1/2-inch drive, but a 3/8-inch to 1/2-inch adapter is included so you can use it with 3/8-inch drive torque wrenches. - Compatible with all Wheels Manufacturing bottom brackets that have 48.5mm or 44mm, 16-notch spline patterns - Also compatible with FSA MegaEVO BB cups, Shimano, SRAM/Truvativ, Campagnolo Ultra Torque, and FSA - Machined 6061 aluminum - Anodized red

- Bearing extractor set for medium bearings - (1) 6002, (1) 6003, (1) 6804, (1)6805

- Machined to match manufacturer specifications and designed to be used with a ½” drive socket or torque wrench for easy installation and removal of e-bike lockrings. - Precision machined aluminum body. - Anodized in Wheels MFG red.

Our 6806 open bore adapter is used to press 42x30 sealed bearings. The adapter is machined with one step at 30mm ID, which fits into the center of the sealed bearing. Common bearing size for BB30 frames and bottom brackets. - Installs: 6806 bearing - Inner step outer diameter: 29. 9mm - Outer diameter: 41. 8mm - Thickness: 7mm - Thru hole diameter: 0. 387" (9. 8mm) - Inner hole sized to fit 1/2" threaded rod - Compatible BP0006, BP0007 - Machined, red anodized aluminum - Sold individually (2 drifts required for some installations)

- Machined to match manufacturer specifications and designed to be used with a ½” drive socket or torque wrench for easy installation and removal of e-bike lockrings. - Precision machined aluminum body - Anodized in Wheels MFG red.

- Machined to match manufacturer specifications and designed to be used with a ½” drive socket or torque wrench for easy installation and removal of e-bike lockrings. - Precision machined aluminum body. - Anodized in Wheels MFG red.

- Similar to its big brother but at a fraction of the size. The new and more efficient Adjustable Press Stop Mini will make life easier for mechanics as it allows for quick and accurate positioning in places where space is tight at the press of a button. - Adjustable Press Stop slides along 3/8" ACME threaded press rod when the button is depressed and can be placed quickly to secure drifts, spacers, and cups when completing maintenance or installation of bike headsets, bottom brackets, and bearings. - Compatible with new and existing Wheels MFG press kits which utilize a 3/8" ACME threaded rod - Compatible kits include: Press-4, ST0006, Press-1 - Machined aluminum body - Anodized in Wheels MFG red. - Durable steel button - For use with 3/8" ACME threaded press rod (Sold Separately)

Thin flange bottom bracket socket designed to create a tight grip on thin flange bottom bracket to avoid slipping while torquing cups into bike frames. This single-sided socket is used for installing and removing 48.5mm, 16-notch bottom bracket cups. The socket has a machined 3/8" drive, which can be used to allow 3/8" drive torque wrenches to be attached and locks onto 1/2 inch unc press rod for secure and easy installation of thin flanged bottom brackets. Machined 6061 aluminum anodized red

- Essential bearing press for installation of bearings with a 10mm minimum ID - (1) 3/8 ACME threaded rod, (2) 30mm standoffs, (2) threaded handles