Dimension Suspension Seatpost - Clamp Style: Std Rails - Diameter: 27.2mm - Length: 350mm - Material: Aluminum - Max Height: 255mm - Min Height: 130mm - Offset (mm): 0mm - Seatpost Type: Suspension - Travel (mm): 35mm - Weight: 450g
Sleek design and ultimate functionality of the WCS 1-Bolt seatpost are the hallmarks of Ritchey design. Single bolt-actuated side load clamp offers easy adjustability and simple security in a post that works as nicely as it looks. - 3D Forged 7050 Alloy - Available in 27.2, 30.9 and 31.6mm diameters - Available in 350 and 400mm lengths - 20mm Offset - 7x7mm saddle rail clamp included - Interchangeable clamps available for carbon rail saddles - Saddle Clamp Torque Spec: 12Nm - Finish: Blatte - 195g (27.2/350)
The latest generation Thudbuster ST is superior to its predecessor in every way. Building on Thudbuster's proven parallel linkage technology we have completely re-designed the seatpost for increased durability, a higher rider weight limit, and additional suspension travel, as well as ease of use through tool-free elastomer change and a single-bolt seat clamp design. By improving on this already legendary design, we're confident to say that the newest generation Thudbuster is the most advanced suspension seatpost ever made. - Travel: 50mm - Weight: 580g - Max Rider Weight: 330lbs
- Highly tested & engineered unidirectional carbon tube offers outstanding fatigue & impact strength for a lightweight XC post - Simple, lightweight 2 bolt design permits the saddle to be installed without disassembling the head - Angled clamp bolts allow easy tool access for hassle free adjustment and tightening - The rubber seatpost grommet fully seals the post to prevent water entering your seat tube - Hunter head is suitable for most rail types 7/8mm alloy rails and 7/9mm carbon - Wide lower cradle gives extra rail support for lightweight saddle rails - Narrow upper cradle increases the amount of forward/back saddle adjustment - Tilt Adjustment 6° up 12° down with Zero offset
The X-Fusion Manic post uses internal cable routing and was designed around a low-profile seat cradle and seal collar to fit a broad range of frames. The mechanism is air-sprung and hydraulically locked. The remote can be run on the left or right, above or below the handlebar, but is optimized as a left shifter replacement for 1x drivetrains. - Cable activated, hydraulic action, infinitely adjustable travel - Double key-way design prevents lateral twisting - Double bolt clamp with a wide range of seat angle adjustment. Fits both standard and 7 x 9 mm Carbon Rails - Sealed cartridge internals for quick replacement - Low profile head-seal and saddle clamp increase useable travel
Bike fit is important. A bike should feel like an extension of the body, especially when dialed-in. Getting just the right saddle position is second-to-none when putting out power over long miles. Ritchey Link posts offer two clamp positions for greater adjustability in dialing-in the right fit. - 7050 Alloy 2pc Press Fit Head - 20mm adjustable setback - Reversible clamp for greater fore/aft adjustability - Length: 350mm
- Designed using SRAM Exogram technology - Available the Zipp SL Speed DI2 Internal Battery Mount to hold a Shimano DI2 seatpost battery within the SL Speed seatpost. (Sold separately) - Matte Black finish
The Ritchey two-bolt post reinvented—lighter, more compliant, and more versatile than ever. Patented LINK clamp works with all standard saddle rail designs as well as Ritchey Vector Evo and Selle Italia MonoLink saddles with separate adapter. LINK Carbon Posts use FlexLogic carbon layup developed for Pro Tour team bikes from Stevens, Canyon, and Scott — 15% more vertically compliant with no loss of lateral or torsional stiffness. 15mm offset with reversible clamp. - Material: lightweight carbon fiber - Saddle clamp: standard rails - Saddle clamp torque: 15Nm (max) - Seat collar torque: 6Nm (max) / 7Nm (max) for Ritchey steel frames - Weight: 145g (27.2x350mm) - Color: matte UD carbon finish
Bike fit is important - a bike should feel like an extension of the body, especially when dialed in. Getting just the right saddle position is second-to-none when putting out power over long miles is concerned. Ritchey Link posts offer two clamp positions for greater adjustability in dialing in the right fit. - 7050 Alloy 2pc Press Fit Head - 15mm adjustable setback - Reversible clamp for greater fore/aft adjustability - Finish: BB black
The Highline 3 delivers infinite adjustment, smooth feel, and easy installation. Details - Premium Trelleborg sealing - Exclusive Igus LL-glide bearings and keys - Jagwire cable and housing - Self-contained hydraulic cartridge delivers industry-leading quality and reliability - Internal routing - Quick connect mechanism for ease of cable installation - Linear actuator for quick return speed - 2-bolt standard head - Remote sold separately
Thomson's Elite Setback Seatpost is perhaps one of the most recognizable bicycle components in the world and it has earned its reputation as a super-strong, light and reliable beauty. With roots in the aerospace industry, Thomson builds the post with a tough and light 7000-series aluminum body, an elliptical extrusion that adds strength and stiffness, and a head and seat clamp forged and machined from a block of aluminum to eliminate any possible weak areas. Plus, its simple-to-use 2-bolt seat clamp allows speedy, infinite and secure seat angle adjustment from minus 5 degrees to plus 29 degrees. Upgrade your favorite ride to a Thomson seatpost and start riding in style.
The all-new Highline delivers infinite adjustment, smooth feel, and easy installation for any bike. Details - Shorter insertion length to fit more bikes - Premium Trelleborg sealing - Exclusive Igus LL-glide bearings and keys - Jagwire cable and housing - Self-contained IFP hydraulic cartridge - Internal routing - Quick connect mechanism for ease of cable installation - Linear actuator for quick return speed - 2-bolt quick-connect head - Remote sold separately
$350.00 - $410.00
3 years of REVIVE out in the market resulted in another benchmark product for BikeYoke: REVIVE 2.0. The new extralong 213mm REVIVE required a lot of re-thinking and re-engineering the whole chassis structure and since we think they deserve it, the shorter REVIVES will also get all the nice updates, and benefit from what was originally implemented only for the longest sibling of the REVIVE family. Noteworthy updates of the REVIVE 2.0 include: - One piece 3D-forged upper tube unit for improved stiffness and strength - Fully hard-anodized pin seats in the upper tube for improved corrosion-resistance - CNC-finished actuation lever for even smoother engagement - New upper saddle clamp and saddle bolts with integrated conical washers for even simpler saddle installation Wanna know more about the REVIVE? What if there was a dropper post, that actually solves and not just improves reliability issues, saves cost and time on the long run, and does not let you worry about too much time spent at service-centers? Or how about “bleeding” your seat post within a few seconds, while it is still installed in your bike? BikeYoke presents the REVIVE dropper post, featuring one of the most brilliant design features in dropper post design in many years. More than 10 years of experience in drop-post design went into the “REVIVE” and the development has finally paid off. Of, course, just as many other companies, BikeYoke would say, that REVIVE is reliable and strong and smooth. And yes, REVIVE is all of that, but not because we tried to improve current designs, but because we were thinking outside of the box and created a new concept, that is completely different from everything before. To understand the benefits over other posts you have to know about the problems of many current designs first. Many of the popular current seatpost designs are based on a hydraulic lockout-system that relies on a perfectly sealing IFP (Internal Floating Piston), separating oil from air to prevent the seatpost from getting sagging or bouncing. There are a lot of difficulties to overcome when using an IFP because an IFP has to maintain 100% sealing function. If air could go to the oil side, your post will start becoming springy. This happens to a lot of posts in the market already and is the main issue why posts need to be serviced. That´s why BikeYoke´s “REVIVE” features a NON-IFP design, because we think it is too difficult - if not impossible - to make a really reliable design using an IFP. REVIVE only requires 2 dynamic seals in the hydraulic circuit: The shaft sealing and the main piston sealing for the lockout mechanism. The highly critical IFP has been removed, and with it the need of perfect concentricity and finish of the sealing surfaces of the tubes. The lack of an IFP also results in the smoothest action you can think of. The most important and ground-breaking feature of Revive is its “REVIVE-VALVE”. Even REVIVE can get air somewhere where it does not belong. This can happen for example when you actuate your seatpost while its upside down. And here is where the patented RESET VALVE comes into play: - Insert a 4mm Hex Key into the REVIVE hex port, turn it and push down the post by hand. - This will reset your hydraulic circuit on the fly - whenever. wherever. This is done just within a few seconds and only by the turn of a 4mm Allen key or the integreated mini reset lever, that comes with the post - of course without even having to remove your drop post from your bike. So, now one might already understand that: - No external air will want go inside the post´s hydraulic circuit, since it is charged with higher pressure, than its surroundings. - No oil will go out (or at least very very little oil over the curse of a long time), because of very stable sealing - external sealing has never been a real problem of current post design - The hydraulic system can be reset to “new” via the unique “REVIVE-valving” - This means the hydraulic circuit is a very stable closed system and basically maintenance free. Still there are parts that will need to be serviced sooner or later and when designing REVIVE it was put a lot of attention to maximum user-friendly serviceability: - Bushings and keyway pins will wear over time. Usually, the pins wear first and you would want to replace them to reset your rotational play. - Exchanging the pins and the lower bushing is simple and does not require any opening of the hydraulic system and can be done within less than 5 minutes. 1 set REVIVE dropper post includes: - 1x REVIVE Seatpost - 1x cable housing 1500mm - 1x inner wire 1700mm - 2x housing endcap - 1x barrel cable clamp - 1x air valve adapter - 1x Quick-Reset-Lever - 1x remote (optional) - 1x BikeYoke I-spec adapter or Splits Clamp (optional) - 1 set titanium saddle bolts and nuts (optional)
Take the edge off. The SAVE Carbon seatpost has been proven in the worlds most challenging bike races. Light, comfortable and incredibly functional. Where it thrives: The open road, up and down hills What it's built for: Comfort, control Highlights: - Ultralight carbon - Subtle compliance = comfort - Di2 internal battery compatible
The name says it all: Thomson's Masterpiece Seatpost combines the best materials, exceptional strength, perfect function, light weight and the classic beauty of all Thomson products. All Masterpiece posts are extruded and then painstakingly machined from a single block of ultra-strong 7000-series aluminum, and they all weigh less than 200 grams complete. This means you get a post tough enough for any ride on or off road and at a nice and light weight that will complement your dream bike. What's more, you get Thomson's easy-to-adjust and super reliable 2-bolt seat clamp that makes it a breeze to dial in your perfect seat position from minus 5 degrees to plus 29 degrees.
The redesigned Zero post offers no-slip saddle engagement and high adjustability by securing the rails with fore and aft bolts. Whether you're hitting rough singletrack or remounting in a hurry, this ensures the saddle stays exactly where you want it. - Material: 2014 alloy - Total length: 400mm (including 100mm of minimum insert) - Saddle clamp: 2-bolt fore/aft - Saddle clamp torque: 7Nm (max) - Seat collar torque: not specified - follow frame/seat binder specification - Weight: 240g (27.2x400mm)
The newly redesigned EC70 Seatpost takes our superlight unidirectional carbon and applies our patent pending ISA technology - Independent Saddle Adjustment - which allows for completely independent fore-aft adjustment and saddle adjustment. With the 2 pitch adjustment bolts, the saddle angle gets locked into place as if you were adjusting limit screws, and unlike single bolt designs, you get adjustability and security. Available in 20mm Setback and Zero configurations. - Finish: Matte Black UD Carbon/Matte Black Head - Weight: Zero offset, 210g; Setback offset, 223g - Head offset: 0mm; 20mm - Length: 350mm w/ 80mm min. insert - Quill size: 27.2mm - Rail clamps: 7mm round; 7mm x 9mm oval (both included) - Material: EC70 carbon
$18.99 - $19.99
Kalloy's 602 seatpost comes in a wide variety of diameters to fit most frames. Simple, sturdy, and lightweight, the 602 makes a great replacement seatpost.
- Length: 400mm - Offset: 0mm - Clamp Style: Standard Rails - Material: Aluminum
The Duncan TRI seatpost is constructed from carbon fiber for ultimate weight saving. The saddle is mounted to a sliding rail, which allows for a wide range of adjustment. - Sliding mount for rail - Carbon fiber - Compatible with Plasma 6 only
The proven Transfer seatpost gets lighter and tighter. Completely redesigned from the ground up, with improved serviceability, decreased weight, reduced length, and decreased insertion depth. Performance Elite Transfer Posts retain the same internals, diameter options, drop options, shortened stack heights, new patent-pending head design and proven internals as the Factory Series but have a black anodized upper. - Cable actuated with tool-free quick disconnect for easier installation and removal - Low lever force provides consistent actuation pressure even with saddle weighted or unweighted - Easy to modulate return speed with lever - Remote lever sold separately - 0mm offset
Thomson Covert Elite Dropper Seatpost-31.6 150mm Black Internal. We've set the bar with the Thomson covert black dropper post. It's designed around internal routing for clean installation and an updated shift style remote lever for effortless operation. The Thomson Covert Dropper includes a new shifter oriented remote lever for easy operation. The cartridge-based system is designed to have the longest service life in the industry. If repair is needed, it's fast, affordable, and simple. Every part that makes up the Covert dropper is carefully chosen, and of the highest grade quality available. - Custom made Norglide bearing bushings and Trelleborg O-Rings and seals - Thomson saddle clamps and fasteners - Motul Oil for durability and precision quality. - The return speed is damped in the last 15mm of upward travel to be gentle on your seating area. - 60mm (Ø27.2 only), 100mm, 125mm, 150mm of infinite travel. - Passes ISO 4210 fatigue and strength tests for seat posts.
TruVativ's Stylo T30 Seatpost is constructed with a 1-piece 3D-forged 7050 aluminum tube to be light and strong. The sturdy dual-bolt head provides loads of adjustability so you can fine tune your saddle position.
- 3D forged from 2014 heat-treated aluminum for optimal strength to weight ratio - Race Face's triple butting design maintains strength in critical areas while reducing overall weight - The tube is anodized & shot peened for increased fatigue life - Updated Hunter head design for easy saddle installation and full adjustability - 3D forged from 2014 heat treated aluminum with triple butted mast - Thumbscrew tightening system allows quick dial-in of the saddle angle by hand - Angled clamp bolts allow easy tool access for hassle free adjustment - Rubber grommet seals the post to prevent water from entering seat tube - Accepts 7/8mm CrMo/alloy and 7/9mm carbon rails. 260g (30.9mm)
The proven 2-bolt design on this classic provides a class-leading balance between strength, weight, and adjustability. The two-bolt design is easy to adjust and holds tight. Its low profile clamp reduces stress on lightweight rails and won't bottom out, and the bolts are oriented to the axis of the rails for the greatest contact area with the saddle. The Classic also features Ritchey's 'Classic' high-polish silver finish. - Material: 2014 alloy - Total length: 350mm (including 100mm of minimum insert) - Saddle clamp: standard - Saddle clamp torque: 13Nm (max) - Seat collar torque: not specified - follow frame/seat binder specification - Weight: 260g (27.2x350mm) - Color: high-polish silver
Ritchey's Comp Link reimagines the two-bolt post, making it lighter, more compliant, and more versatile than ever. The patented LINK clamp works with all standard saddle rail designs as well as Ritchey Vector Evo rails. - 6061 aluminum 2-piece press-fit construction - Diameters: 27.2 and 31.6mm - Offset: 20mm - Reversible clamp allows for an additional 10mm of fore-aft saddle adjustment - Length: 400mm - 284g (27.2x400mm)
The Syncros Dropper 2.0 seatpost gives you the freedom to quickly switch from sprinting uphill or attacking down a descent with the simple press of the remote. Internal cable routing, infinite steps and 120mm or 150mm of travel round out this lightweight package. - Alloy AL7050 - 31.6mm diameter - 10mm Offset - Compatible from 7x7mm up to 7x10mm rails, carbon rails inclusive
The latest generation Thudbuster LT is superior to its predecessor in every way. Building on Thudbuster's proven parallel linkage technology we have completely re-designed the seatpost for increased durability, additional suspension travel, as well as ease of use through tool-free elastomer change and a single-bolt seat clamp design. By improving on this already legendary design, we're confident to say that the newest generation Thudbuster is the most advanced suspension seatpost ever made. - Travel: 90mm - Weight: 750g (31.6mm) - Max Rider Weight: 250lbs
Seatposts can easily be mistaken for a simple alloy or carbon tube, but it’s an essential part of your equipment. The amount of flex in a seatpost determines the comfort of your ride. Pro Vibe seatposts have the right amount of stiffness to ensure maximum power transfer without losing comfort. Align all forces to work in favor of you—go for the PRO Vibe seatposts. - 3D forged AL-2014 - Innovative 1 bolt clamping system - Weight: From 234g
ENVE's proven twin-bolt seatpost design refined for the modern road bike with seatpost battery integration capabilities. - Material: Carbon Fiber - Hardware Material: Titanium - Saddle Angle Adjustment: 0 – 27 degrees - Saddle Rail Compatibility: 7x10mm Carbon Rails / 7mm Round Alloy Rails - Torque Spec, Saddle Rail Clamp Bolts: 5.5Nm - Torque Spec, Seatpost Collar: Determined by your Frame manufacturer/Seatpost Collar - Weight: 210g (25.4mm), 204g (27.2mm), 204g (30.9mm), 204g (31.6mm)
Page 1 of 4 Next page