Parts & Accessories
The buyer's choice for wheel builders looking to save weight. ProLock nipples contain a special adhesive compound (by Loctite) which is activated when a spoke is threaded into the nipple, forming a durable bond. - 32 nipples weigh approximately 30 grams
$8.00 - $50.00
Whisky’s tubeless rim tape is designed to make setup as easy as possible. Elasticity allows for smooth, even adherence while translucency lets you see where the tape contacts the rim. Different widths available to fit almost any rim.
Wheel Freehub Kit—XD Driver Body Kit—ZM1 3Zero - Compatible With: WH-MOTO-30-A1
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
SRAM's Quick Releases hold your wheel tightly in place, are built for ease of use and made to last, too. You get a front and rear quick release.
$15.99 - $17.99
Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.
$15.00 - $20.00
Stan's 3.30/3.30Ti Hub Kit converts Stan's 3.30 front hubs from quick-release to through-axle compatible. Installation is easy—just pull the old ones off and put the new ones on. Conversion kits available in 12mm and 15mm.
$8.99 - $13.99
WTP's Helix hub guards are designed to work on The Helixline of hubs, replacing the cones for a perfect fit without having to spread your dropouts. - Includes heat-treated chromoly adaptor to replace hub cone nuts for a perfect fit - Rear Hub guards are compatible with Helix V1 and Helix V2 freecoaster hubs and many other "KHE" style freecoasters on the market
Convert Roval wheels with 142 or 142+ to be used with Boost spacing (110 /148mm) suspension forks and frames. - Kits include front and rear hub end caps, rotor spacers, and kit specific rotor bolts - Compatible with select MY13-16 Roval Wheels. Choose the appropriate SKU for each wheelset - Each conversion kit requires the existing rear wheel to be re-dished to center. Consult an authorized dealer to perform this operation
$42.00 - $48.00
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
You need rim tape to keep your tubes from blowing through the spoke holes, especially when landing big airs. WeThePeople's got your back, though. If your's is questionable, you better replace it with this WTP Nylon Rim Tape, a perfect fit with Logic Rims. - Strong - Lightweight - Tube-proof
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening
$62.00 - $69.00
Yes! A 12mm thru-axle adapter for BOB Trailers. These Robert Axles for BOB Trailers are specifically engineered to attach the proven BOB Trailer to your thru-axle-equipped bike. Take full advantage of your modern bike with 12mm thru-axles and harness the rigidity of the thru-axle to haul your BOB Trailer. Set out on any adventure, big or small. Great for off-road tours, trail building, hauling cargo, and more! - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The axle ends are stainless steel which allows for mounting of the BOB Trailer bobbins. - No special tools required. The design allows for wheel installation or removal using your standard 5mm hex wrench. - Please note: This axle does not come with the BOB Trailer bobbins (those are available separately). Or, you can reuse your bobbins from the stock BOB Trailer Quick Release that came with your trailer. - Designed, built, and quality tested in the USA. Proven around the world.
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.
$6.95 - $7.95
Lightweight and easy to install, there are Ritchey rim strips for all wheel sizes and types. - Easily snaps over your rims - Stretchy, tightly woven material provides a close fit and protects from abrasion - Sold as a pair - Not for tubeless set up
Hop up your rig with these custom rim decals. Available for the entire Arc rim range (24mm—45mm), as well as Aeffect SL, R, and Plus. Each set comes with enough decals to do a complete wheelset (2 wheels). Now your bike can be as pro as your riding kit! - Full set of decals for a wheelset (2 wheels)
$58.00 - $65.00
Purchase our Kid Trailer axle for your bike, and share your stoke for cycling with your kids. Simplify your life by allowing quick and secure attachment of your trailer to your best and favorite bike. Enjoy the adventure. Robert Axles for Kid Trailers are designed specifically to fit your 12mm thru-axle bike and allow attachment of any hitch-mounted trailer. These fit any trailer that has two wheels and a single point of attachment to the axle. This includes all the two-wheeled child, pet, and cargo trailers such as Thule, Chariot, Burley, Instep, Carry Freedom, and many more. - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The stainless steel axle end allows for mounting of the hitch provided with your trailer. - Hardware for attachment of the hitch is included; the hitch, itself, is not. - No special tools required. Design allows for wheel installation and removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
$8.00 - $16.00
Whisky Parts Co. Tubeless Rim Tape.
Stan's original Neo hub has evolved to be stronger and more reliable than ever. The additional stress of larger cassette cogs, more capable bikes, and even more challenging trails led to the creation of the Neo with Speedsync. This CNC machined Speedsync freehub is a direct replacement for your Neo hub and includes pawls, springs, pawl retaining ring, and 2 red freehub spacers. Bearings are pre-installed. Note: - Singlespeed freehub cannot be used to convert a hub originally set up with a Shimano or Sram XD freehub to SS. This freehub is only to be used with Stan's Neo SS hubs. - OneUp freehub WILL NOT WORK with a SRAM cassette or Shimano cassette without a One Up Shark Cluster.
DT Swiss Standard Front Quick Release Skewers. - Traditional cam-operated lever - Stainless steel shaft
$116.30 - $133.00
Freehub bodies for Zipp Cognition hubs.
- Longer skewers fit modern frames/forks with thicker dropouts - Aluminum lever/nut, Delrin pivot washer, serrated alloy nut with Nylock - White skewers are powder-coated - Shaft: chromoly - Wheel: front/rear - Spacing (front/rear): 100/135mm - Weight: 112g/set
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
- Anodized aluminum or plated brass. - 50 per bag - 16mm length
- Decals for replacement rims
The Double Wheel Travel Bag is designed so your wheels sit offset — without axles or cassettes damaging each other. The Double Wheel Bag features a durable Cordura shell, high density padding to prevent damage, zippered closure system and can fit most size wheels from 700c to 26-inch.
Front axle and endcap kits for all non-boost 2017 cobalt, iodine, and zinc wheels. Use this front axle and endcap kit to convert any non-boost 2017 cobalt, iodine, or zinc wheel to the size selected below.
Durasync freehub bodies feature triple freehub bearings for increased axle stability to handle even greater vertical and torsional loads. This CNC machined durasync freehub is a direct replacement for your Neo hub, and includes pawls, springs, pawl retaining ring, and red freehub spacer. Bearings are pre-installed. - 6-pawl system provides 36 points of contact and 10-degree engagement for quick acceleration - Chromed steel bearings - Wide bearing stance and axle design reduces flex and adds durability - Low drag main seal prevents contamination and reduces resistance - Mini Driver has a Shimano HG spline, but is 10mm shorter to accept 11-speed cassettes with 10t cogs from Hope and OneUp Components
Maximum stiffness and highest safety—the RWS quick release for road and MTB. Our patented RWS axle system is stiffer, safer, and easier to use than conventional quick-release axles. The RWS quick release is absolutely reliable and offers a strong connection to the frame. The perfect choice for anyone who is looking for maximum performance and safety.
Travel in style with the Roval Single Wheel Bag. It features padded Cordura nylon construction and is reliably tough and weather-resistant, while the bag itself is built to accommodate a single wheel. Accommodates 26" and 700c sized wheels.
Page 1 of 2 Next page